






Toyota Tacoma Truck Topper | ARE Truck Caps
Our CX Series topper transforms your Tacoma bed into secure, weatherproof storage without sacrificing the truck’s clean lines. We engineer every topper specifically for the Tacoma’s bed dimensions — short bed, long bed, and Access Cab configurations — ensuring factory-level panel gaps and a flush fit with your truck’s existing stake pockets.
The .100-inch marine-grade aluminum construction resists dents and corrosion while keeping weight under 180 pounds for one-person installation. Three-point rotary paddle locks secure both side windows and the rear door, and continuous weather stripping creates a dust-tight seal even on washboard roads. We match Toyota’s full paint palette through a multi-stage process that bonds primer, basecoat, and clearcoat directly to the aluminum.
Construction & fit details

Aluminum Construction & Finish
We build the CX frame from .100-inch marine-grade aluminum extrusions welded at every joint — the same alloy spec commercial contractors trust for permanent outdoor enclosures. Aluminum won’t rust through like steel or develop stress cracks the way molded fiberglass does after years of expansion and contraction.
The finish process starts with a chromate conversion coat that etches the raw aluminum, followed by two-part epoxy primer, your selected basecoat color, and two layers of UV-stable clearcoat. We can match any Toyota paint code including the tri-coat metallics introduced on the 2024 Tacoma TRD Pro models. The paint bonds directly to the aluminum substrate rather than sitting on gelcoat, so stone chips expose gray metal instead of white fiberglass fuzz.

Weather Sealing & Window Systems
Continuous EPDM rubber stripping runs the full perimeter of the base rail with steel-reinforced corners that compress evenly against the Tacoma’s bed rail. The rubber maintains its compression set below freezing and doesn’t harden in direct sun the way cheaper vinyl seals do after two or three summers.
Both side windows use a horizontal slider design with internal fiberglass screens — you can crack them for ventilation without letting in rain or insects. Each slider locks independently with a three-point rotary paddle that engages strikes at the top, middle, and bottom of the frame. The same paddle mechanism secures the rear barn doors.
Tacoma Bed Compatibility
The CX is manufactured in bed-specific molds for every Tacoma generation from 2005 forward. Short bed (60.5 inches), long bed (73.7 inches), and Access Cab beds each get a dedicated tooling setup — we don’t use adjustable universal frames that require shims or gap fillers.
Panel gaps between the topper and cab glass measure 3/8 inch or less when properly installed, matching the factory tolerances Toyota holds on the tailgate-to-bumper fit. The base rail sits flush with the top edge of the bed side without overhang, and the topper’s front radius follows the cab contour so there’s no aerodynamic parachute effect at highway speeds. Owners with cab-height bed racks or crossbars should verify clearance before ordering — the CX roof height is 20 inches at the centerline, tapering to 18 inches at the sides.



More ARE Toppers for Popular Trucks
Rated 4.8 by verified buyers








Common Questions About the Tacoma Topper
Yes — the CX clamps attach to the factory stake pockets which sit above most drop-in and spray-in bed liners. The base rail includes 1/4-inch rubber isolator pads that compress slightly to accommodate the liner’s raised edge.
If you have a thick LINE-X or Rhino liner with buildup around the stake pockets, you may need to trim the liner flush with the pocket opening so the clamp hook can engage the metal flange underneath. We recommend test-fitting the clamps before final installation to verify engagement.
The CX roof uses reinforced mounting channels that accept most aftermarket crossbar systems designed for truck toppers. We offer an ARE-branded rack kit with adjustable crossbars and tie-down cleats, or you can use third-party systems like Yakima or Thule that bolt into the factory channels.
The aluminum roof skin is rated for 150 pounds of dynamic load when weight is distributed across two crossbars. For heavier gear like rooftop tents, we recommend our MX Series which has a thicker roof panel and integrated rack rails.
You provide your Tacoma’s paint code from the door jamb sticker when you place your order. We mix the exact OEM formula Toyota supplies to body shops and spray the topper in our climate-controlled booth using the same multi-stage process as the truck factory.
Solid colors like Super White or Midnight Black typically ship in four weeks. Tri-coat finishes like Lunar Rock or Army Green require an extra basecoat layer and cure cycle, extending lead time to six or seven weeks. We send you photos of the finished topper next to a color chip before shipping for final approval.
The continuous EPDM weather stripping creates a compression seal against the bed rail that keeps out water in normal driving rain and automated car washes. The side windows and rear doors use the same rotary paddle locks with rubber gaskets that seal when the paddles are engaged.
We don’t recommend using high-pressure wands pointed directly at the seals from less than six inches away — that can force water past any weather seal through hydraulic pressure. For touch-free washes and normal rain, the topper stays completely dry inside.
No — the Tacoma tailgate must be lowered before you can open the topper’s barn doors. The doors swing outward and down, and they require clearance past the tailgate’s top edge.
If you need access to the bed without lowering the tailgate every time, the side slider windows provide a reach-through opening that’s large enough for toolboxes, grocery bags, and most camping gear. Some owners also install a small porthole or T-handle access door in the front panel for quick retrieval of frequently used items.
Most owners report a 1-2 MPG improvement in highway fuel economy after installing the CX compared to driving with an open bed. The topper smooths airflow over the bed and eliminates the turbulent low-pressure zone behind the cab that creates drag.
The aerodynamic benefit is most noticeable at speeds above 55 MPH. City driving shows little change in fuel consumption. Actual results vary based on driving habits, tire size, and whether you’re running a leveling kit or lift.
We warranty the welded aluminum frame and all structural joints against defects in materials and workmanship for as long as you own the topper. This includes the base rail, corner posts, roof frame, and door frames.
The paint finish carries a five-year warranty against fading, peeling, or delamination. Weather stripping, latches, gas shocks, and window mechanisms are covered for three years. The warranty is non-transferable and requires proof of purchase from an authorized ARE dealer.






