






LEER Roof Rack | Professional-Grade Truck Cap Roof Systems
Our LEER roof rack system mounts directly to your truck cap, adding professional-grade cargo capacity without compromising aerodynamics or fuel efficiency. Engineered from aircraft-grade aluminum with a powder-coated finish, this rack system handles everything from kayaks and lumber to rooftop tents and work equipment.
The T-slot rail design accepts most aftermarket crossbars and accessories, giving you complete flexibility to configure your setup for any job or adventure. We built this system for contractors, outdoor enthusiasts, and anyone who needs their truck to work harder.
Key specifications & load capacity

Load Capacity & Weight Distribution
The LEER roof rack carries a 500 lb dynamic load rating when properly distributed across the full rail system. That translates to two full-size kayaks, a rooftop tent with two adults, or stacked lumber up to twelve feet. Static load capacity increases to 200 lb when the vehicle is parked, making overnight rooftop camping fully supported.
Weight must be distributed evenly across both rails. We engineered the mounting brackets to transfer load directly into your cap’s aluminum frame, bypassing the fiberglass shell entirely. Each bracket location is reinforced at the factory during cap assembly, so retrofit installation maintains the same structural integrity as factory-equipped units.

Installation & Cap Compatibility
Every LEER truck cap ships with pre-drilled mounting points for our roof rack system. Installation takes fifteen minutes with zero drilling or permanent modification to your cap. The clamp-style brackets slide into factory channels and tighten with thumb screws, allowing you to remove the entire rack for seasonal storage without leaving visible holes.
The system fits all LEER 100-Series caps manufactured after 2015, plus most 180-Series and DCC models. Older caps may require adapter brackets, which we stock for common bed lengths. If you’re adding a rack to an existing LEER cap, contact our installation team to verify bracket compatibility for your specific model year.
Crossbar Options & Accessory Integration
T-Slot Rail System
Our T-slot rail design accepts Thule, Yakima, and Rhino-Rack crossbars without adapters. The 30mm slot spacing matches industry-standard mounting patterns, so you can swap crossbars between vehicles or upgrade to specialized carriers as your needs change. We’ve tested compatibility with over forty aftermarket roof accessories, from bike trays to cargo boxes.
Integrated Tie-Down Points
Eight integrated D-rings run the length of both rails, spaced every sixteen inches. These flush-mount anchors accept standard ratchet straps and cam buckles for securing loose cargo like kayaks, lumber, or camping gear. The D-rings rotate 360 degrees and lock in place with a quarter-turn, preventing strap twist during highway driving.



Complete Your LEER Setup
Rated 4.8 by verified buyers








Common Questions About LEER Roof Racks
The LEER roof rack system is engineered specifically for LEER truck caps with factory mounting channels. It will not fit caps from other manufacturers without significant modification. If you own a non-LEER cap, contact our team to discuss universal rack alternatives that mount to your specific cap's roof profile.
Installation is fully DIY with zero tools required. The clamp-style brackets slide into pre-drilled channels on your LEER cap and tighten with oversized thumb screws. Most owners complete installation in under twenty minutes. We include step-by-step instructions with photos, and installation videos are available on our support page.
The system is rated for 500 lb dynamic load when the vehicle is in motion, distributed evenly across both rails. Static load capacity increases to 200 lb when parked, which safely supports rooftop tents with two adult occupants. Always verify your truck's gross vehicle weight rating and roof load limit before adding cargo.
Installing the LEER roof rack does not void your cap warranty. The rack mounts to factory-reinforced points and does not penetrate the fiberglass shell. We recommend professional installation for fleet or commercial applications to maintain documentation, but DIY installation using factory hardware preserves all warranty coverage.
Yes. The clamp brackets release with thumb screws and the entire rack lifts off in one piece. Removal takes about ten minutes and leaves no visible hardware on your cap. Many owners remove their racks seasonally to maximize fuel economy during winter months when rooftop cargo isn't needed.
The low-profile design minimizes aerodynamic drag compared to traditional raised crossbars. Independent testing showed a 1-2% fuel economy reduction with the rack installed empty, versus 4-6% for cab-mounted crossbars. Actual impact varies with vehicle speed, crossbar selection, and cargo shape.
The 30mm T-slot rail accepts Thule, Yakima, Rhino-Rack, and most aftermarket crossbars without adapters. We've verified compatibility with over forty rack systems. If you already own crossbars, check the manufacturer specifications for T-slot or channel-mount compatibility. Our team can confirm fitment for specific crossbar models.






