






A.R.E. Z Series Truck Cap | Premium Aluminum Construction
The Z Series represents our flagship aluminum truck cap, engineered for contractors and fleet operators who demand maximum durability without excess weight. We build every Z Series cap with extruded aluminum framing and .050-gauge aluminum side panels, delivering a structure that resists dents and corrosion season after season.
This cap mounts flush to your truck bed using our patented Sure-Seal bulb seal system, eliminating gaps that let in dust and water. Three-point stainless steel rotary latches on the rear door provide tool-free access, while tinted sliding side windows with screens offer ventilation control. The Z Series ships with a reinforced roof rated to carry 500 pounds of distributed load, making it the go-to choice for ladder racks and rooftop cargo systems.
Z Series construction & fit details

Aluminum Frame Construction & Weight Savings
We machine the Z Series frame from continuous aluminum extrusions rather than roll-formed steel, which reduces overall weight by approximately 35% compared to steel-framed alternatives. A Z Series cap for a full-size 6.5-foot bed weighs roughly 185 pounds, allowing one person to mount or remove it using our optional clamp system.
The .050-gauge aluminum side panels resist the surface dents common with fiberglass shells, and the material’s natural oxide layer prevents rust even when minor scratches expose bare metal. We finish every panel with automotive-grade urethane paint that’s baked at 450°F, creating a bond that won’t flake or peel under UV exposure. Our paint-matching service references factory color codes for Ford, Chevy, Ram, Toyota, and Nissan trucks manufactured since 2000.

Weatherproofing & Bed Access
The Sure-Seal system encircles the entire bed rail contact surface with a compressed bulb seal that adapts to minor bed rail variations, maintaining pressure even as the truck frame flexes over uneven terrain. We anchor the cap using integrated C-clamps spaced every 18 inches, eliminating the drilled mounting holes that create rust points on the bed rail.
Our rear door uses three independent rotary latches positioned at the top corners and center bottom, distributing closing force evenly to compress the tailgate seal. Dual hydraulic prop rods hold the door at any angle between 45 and 90 degrees, and the prop rods detach without tools when you need to remove the entire door for loading oversized cargo.
Roof Load Capacity & Accessory Integration
Structural Reinforcement
The Z Series roof incorporates crosswise aluminum ribs spaced 12 inches apart, each rib extending from side rail to side rail and bonded with structural adhesive before riveting. This grid distributes point loads across the entire roof surface, allowing you to mount ladder racks, roof baskets, or kayak carriers without reinforcement plates. We rate the roof at 500 pounds of distributed load when the cap is properly clamped to the bed.
Factory Rack Mounting Points
We install threaded inserts at six locations along each side rail, spaced to align with industry-standard crossbar systems from Thule, Yakima, and TracRac. These inserts accept M8 bolts and eliminate the need to drill through the roof skin when adding cargo accessories. The same aluminum construction found in their CX Classic and CX Evolve series carries over to the Z Series with additional reinforcement ribs for the higher load rating.



Other Commercial-Grade ARE Truck Caps
Rated 4.8 by verified buyers





Z Series Truck Cap Questions
Yes, the Sure-Seal bulb seal compresses enough to accommodate spray-in liners up to 1/4 inch thick on the bed rails. We include spacer shims with every cap that raise the mounting clamps to compensate for the liner thickness, ensuring even pressure distribution around the entire seal perimeter.
If your liner extends more than 1/4 inch above the original bed rail surface, we recommend having the liner installer trim the rail cap area before mounting the cap. Most professional liner shops can do this during the original application using a heated blade to create a clean transition zone.
Loosen all perimeter clamps using a 1/2-inch socket until they're finger-tight but not fully removed. Disconnect the interior light wiring at the quick-disconnect plug near the front panel, then lift the rear of the cap approximately six inches and slide it backward off the bed rails.
The cap weighs around 185 pounds for a standard 6.5-foot bed, which most people can handle solo by lifting from the rear door opening and walking it backward. We offer an optional aluminum dolly with locking casters that supports the front edge during removal, making one-person operation easier if you remove and reinstall the cap frequently.
We offer a factory third brake light kit that mounts above the rear door and connects to your truck's existing brake light circuit through a quick-splice connector. The light housing matches the cap's exterior color and uses the same LED modules as our interior dome light for consistent brightness and color temperature.
Installation requires routing a wire from the light housing down through the rear door frame to a junction box near the tailgate, where it splices into the center high-mounted stop lamp circuit. The entire installation takes approximately 45 minutes and requires only a wire stripper and electrical tape.
The Z Series uses extruded aluminum framing and aluminum skin panels, while our fiberglass models like the CX Classic use a molded fiberglass shell over an internal wood or aluminum frame. Aluminum construction weighs less, resists impact dents better, and never develops the stress cracks common in fiberglass around mounting bolt holes.
Fiberglass caps generally offer smoother exterior surfaces and better paint color matching for metallic and pearl finishes, since the gelcoat can be tinted more precisely than baked-on paint. Aluminum caps like the Z Series excel in commercial applications where durability and load capacity outweigh cosmetic perfection.
Independent testing shows the Z Series reduces highway fuel economy by approximately 0.5 to 1.2 mpg compared to an uncovered bed, depending on your truck's aerodynamics and typical highway speed. The cap's low profile and flush mounting minimize the aerodynamic penalty, especially compared to open tailgate driving or poorly sealed tonneau covers.
The aluminum construction's lighter weight compared to fiberglass caps helps offset the aerodynamic drag, particularly during city driving and acceleration. Most Z Series owners report the fuel economy impact is negligible compared to the security and weather protection benefits.
We offer a snap-in carpet kit that covers the interior roof and side panels with marine-grade carpet bonded to 1/4-inch foam backing. The kit includes pre-cut panels that attach using automotive trim clips pressed into existing mounting holes, so no drilling or adhesive is required.
The carpet kit reduces interior noise by approximately 40% and provides a finished appearance similar to our fiberglass caps' standard interiors. The marine-grade material resists moisture and mildew, and you can remove individual panels for cleaning or replacement without disturbing the cap's weatherproofing.
ARE backs the Z Series with a limited lifetime warranty on the aluminum frame and structural components against manufacturing defects, corrosion, and structural failure. The painted finish carries a five-year warranty against peeling, cracking, or delamination under normal use and maintenance.
Moving parts including latches, hinges, and prop rods are covered for three years from the original purchase date. The warranty transfers to subsequent owners as long as you register the cap within 90 days of installation and maintain proof of purchase.





